Search found 428 matches

by Bumpkin
Sun May 02, 2010 2:30 pm
Forum: Technical Discussion
Topic: Stage 1 Manifolds
Replies: 7
Views: 3793

Thanks MAP. I have just got around to wire brushing my manifolds and they are exactly the same.
Thanks again
Tel
by Bumpkin
Fri Apr 30, 2010 4:52 am
Forum: Technical Discussion
Topic: Stage 1 Manifolds
Replies: 7
Views: 3793

Beautiful
These came of a Stage 1, but who is to say they are the proper part. I'll have a good look again later.
Thanks
Tel
by Bumpkin
Tue Apr 27, 2010 3:17 pm
Forum: Technical Discussion
Topic: Stage 1 Manifolds
Replies: 7
Views: 3793

Stage 1 Manifolds

Hi Chaps
Got a request here.I have turned out all my Stage 1 bits as i need to sell it all. I have what i think is a set of Manifolds but not quite sure. Do these look like yours?
[img][img]http://img.photobucket.com/albums/v201/ ... C00114.jpg[/img]
Thanks[/img]
by Bumpkin
Tue Apr 27, 2010 5:36 am
Forum: Technical Discussion
Topic: Overdrive Maintenance
Replies: 7
Views: 3509

The only reason i only used my overdrive as a 5th gear only was so it would last longer. Yes i agree that the warning plate inside the cab did state to use the overdrives in 3rd and 4th only.
Tel
by Bumpkin
Sun Apr 25, 2010 8:51 pm
Forum: Sales and Wants
Topic: Left over Stage 1 bits
Replies: 3
Views: 2159

Ebay

Hi
All on EBAY now.
Thanks
by Bumpkin
Fri Apr 23, 2010 4:56 am
Forum: Sales and Wants
Topic: Left over Stage 1 bits
Replies: 3
Views: 2159

Its the relay. Could not remember what they were called.
Tel
by Bumpkin
Thu Apr 22, 2010 3:31 pm
Forum: Sales and Wants
Topic: Left over Stage 1 bits
Replies: 3
Views: 2159

Left over Stage 1 bits

Probably wont have another one now so this lot needs to go 1 complete Stage 1 front axle. 1 pair of complete Stage 1 hubs. Rear exhaust section. Various transmission tunnel panels bits. LT95 gearbox. Complete Stage 1 Steering setup (Steering wheel to wheel hub) 2 Stage 1 unique steering relays. 1 se...
by Bumpkin
Thu Apr 22, 2010 6:09 am
Forum: Technical Discussion
Topic: Overdrive Maintenance
Replies: 7
Views: 3509

I think the Lt95 unit is strong enough provided you dont use them in the low gears. The V8 torque is just to much. Use them as a 5th gear and they go on forever. Look after em as there are very few replacement spare available now.
Tel
by Bumpkin
Wed Apr 21, 2010 7:56 pm
Forum: Technical Discussion
Topic: Overdrive Maintenance
Replies: 7
Views: 3509

Raggylad. The LT95 overdrive is constantly splashfed down the 2 channels on the inside next to the mainshaft cog. Unless the 2 holes at the end of the channel become clogged there should be no oil starvation.
Tel
by Bumpkin
Sun Feb 07, 2010 9:13 pm
Forum: Introductions and Photos
Topic: New Series 3 Stage 1 owner
Replies: 21
Views: 9010

Im actually a ex Stage 1 owner. I'll have another one day. I just had to get pratical.Theres a chap not far from you in Thetford called Glencoyne engineering, hes the man for Stage 1 info. In the low hundreds is good.try Photo bucket to host your piccys so as you can post them on the forums.
Tel
by Bumpkin
Sun Feb 07, 2010 8:25 pm
Forum: Introductions and Photos
Topic: New Series 3 Stage 1 owner
Replies: 21
Views: 9010

Hmm
Some people have all the luck. How much did you get her for?Can we see some more piccys.
Tel
by Bumpkin
Mon Feb 01, 2010 9:39 pm
Forum: Technical Discussion
Topic: Need for overdrives?
Replies: 42
Views: 17230

Jamie One of the main reasons for overdrive failure on the smaller series units is oil starvation. This was cured on the LT95 unit as it is splash fed. I dont know quite how gears and stress work but i do know the most common way to trash a lt95 overdrive is to put to much torque through the unit in...
by Bumpkin
Thu Jan 14, 2010 5:17 pm
Forum: Technical Discussion
Topic: Need for overdrives?
Replies: 42
Views: 17230

Image
Image
Image
Home made overdrive rod.
by Bumpkin
Mon Jan 04, 2010 8:41 pm
Forum: Technical Discussion
Topic: Need for overdrives?
Replies: 42
Views: 17230

I have sold my Stage 1 now but still have bits left over.On the O/D unique linkage, it is very simple to make.I copied an original bar by just beating a length of 12mm bar in the vice with a lump hammer to create the same part. Drilled a hole each end and made the slot with a slitting disc in a 5" a...
by Bumpkin
Wed Dec 30, 2009 7:46 pm
Forum: Technical Discussion
Topic: Body Pannels
Replies: 10
Views: 4052

Call me. 07890946493. I will check tomorrow to make they are still there. Should be.
Terry